Voltage Follower: Definition, Gain, Circuit and Applications

Key learnings

  • A voltage follower is an operational amplifier (op amp) circuit whose output voltage closely follows its input voltage.
  • It has a voltage gain of approximately one: it buffers a signal without intentionally increasing or decreasing its voltage.
  • Its high input impedance helps prevent the signal source from being heavily loaded.
  • Its low output impedance helps it drive a load, within the op amp’s voltage and current limits.
  • A voltage follower can buffer the output of a voltage divider so a connected load has less effect on the divider voltage.
  • The op amp gets the energy to drive the load from its power supply. A follower does not create power or provide unlimited output current.

What is a voltage follower?

A voltage follower, also called a buffer amplifier or unity-gain buffer, is an op amp connected so that its output voltage follows its input voltage.

Its ideal voltage relationship is:

V_{\text{out}} = V_{\text{in}}

The output is not intended to be larger or smaller than the input. Instead, the circuit helps connect a signal source to a load that might otherwise change the source voltage.

A voltage follower is useful when a source can provide only a small amount of current, but the connected load needs more current. The op amp’s input draws very little current from the source, while its output stage supplies current to the load using energy from the op amp’s power supply. Texas Instruments describes the buffer as a circuit with high input impedance and low output impedance, commonly used to drive low-impedance loads, ADC inputs, and reference voltages. TI buffer circuit design

Voltage follower circuit connection

A basic op amp voltage follower is connected as follows:

  1. Connect the input signal to the non-inverting (+) input.
  2. Connect the op amp’s output directly back to the inverting (−) input.
  3. Take the circuit output from the op amp’s output pin.
  4. Connect the op amp’s power-supply pins to suitable positive and negative supply rails, or to an appropriate single supply.

This direct output-to-inverting-input connection is negative feedback. If the output is slightly different from the input, the feedback causes the op amp to adjust its output toward the input voltage, as long as the op amp is operating within its limits.

A simple text representation is:

Input signal ───────> (+) op amp
                       (−) <──── Output
                              │
                              └── feedback connection

The feedback wire runs from the output to the inverting input. The input signal goes to the non-inverting input.

Voltage follower gain

Voltage gain is the ratio of output voltage to input voltage:

A_v = \frac{V_{\text{out}}}{V_{\text{in}}}

For an ideal voltage follower:

A_v = 1

A gain of one is also called unity gain. In decibels, this voltage gain is:

20\log_{10}(1) = 0\ \text{dB}

So, a follower does not provide voltage gain. It provides buffering: it allows one circuit to supply a signal voltage to another circuit with less interaction between them.

Does a voltage follower increase current?

The output may supply more current to a load than the input signal source supplies to the op amp’s input. But that load current comes from the op amp’s power-supply connections, not from the input signal.

The op amp therefore does not create energy. It uses energy from its supply rails to produce the output current. The maximum output current and voltage swing depend on the particular op amp, its supply voltage, and the load. Always check the device datasheet.

Input impedance and output impedance

Input impedance describes how much a circuit opposes current drawn from the signal source. A voltage follower is designed to have high input impedance, so it usually draws little current from the preceding circuit.

Output impedance describes how much the output voltage changes as load current changes. A voltage follower is designed to have low output impedance, which helps it drive a load more effectively than the original source alone.

These properties explain why a follower can buffer a weak source:

  • The source sees a high-impedance op amp input.
  • The load is driven by the op amp output.
  • The op amp’s power supply provides the energy needed for the output current.

Real op amps do not have infinite input impedance or zero output impedance. They also have limits such as input offset voltage, input bias current, output current, bandwidth, and output-voltage swing.

Voltage follower with a voltage divider

A voltage divider can create a smaller voltage from a larger one. Two resistors, R1 and R2, connected in series divide the input voltage. If the output is taken across R2, the ideal unloaded output is:

V_{\text{out}} = V_{\text{in}}\frac{R_2}{R_1+R_2}

If the load connected to the divider draws significant current, it changes the effective resistance of the lower part of the divider. This can change the output voltage.

A voltage follower placed between the divider and the load reduces this loading effect:

Input voltage → resistor divider → voltage follower → load

The op amp’s high input impedance means the divider supplies very little current to the follower input. The op amp output then drives the load, within the op amp’s ratings.

Worked example: buffering a divider

A 10 V source is connected to two equal 10 kΩ resistors. The divider’s unloaded midpoint voltage is:

V_{\text{divider}} = 10\ \text{V}\times\frac{10\ \text{k}\Omega}{10\ \text{k}\Omega+10\ \text{k}\Omega} = 5\ \text{V}

Now connect a 1 kΩ load directly across the lower 10 kΩ resistor. The load and lower resistor are in parallel. Their combined resistance is approximately:

R_{\text{lower,eq}} = 10\ \text{k}\Omega \parallel 1\ \text{k}\Omega \approx 909\ \Omega

The loaded divider output becomes:

V_{\text{loaded}} = 10\ \text{V}\times\frac{909\ \Omega}{10\ \text{k}\Omega+909\ \Omega} \approx 0.83\ \text{V}

The load has pulled the divider output down from 5 V to about 0.83 V.

If a voltage follower is placed between the divider and the 1 kΩ load, the divider can remain close to 5 V because the op amp input draws little current. The follower output can then supply the load current, provided the op amp can deliver the required current and voltage.

At 5 V across 1 kΩ, the load current is:

I_{\text{load}} = \frac{V_{\text{out}}}{R_{\text{load}}} = \frac{5\ \text{V}}{1\ \text{k}\Omega} = 5\ \text{mA}

The op amp must be able to supply this current. A voltage follower cannot maintain the intended output if the load current exceeds the op amp’s capability.

Advantages of voltage followers

Voltage followers can be useful because they:

  • Reduce loading on a high-impedance signal source.
  • Provide a low-impedance output to drive a suitable load.
  • Help isolate two circuit stages electrically, while sharing the same ground and power system.
  • Preserve the input voltage approximately, without intentional voltage amplification.
  • Can buffer reference voltages, sensor outputs, and voltage-divider outputs.

A voltage follower does not provide galvanic isolation. The input and output circuits remain electrically connected through the op amp and their circuit references. Use an isolation amplifier or another suitable isolation device when electrical isolation is required.

Applications of voltage followers

Buffering sensors

Some sensors produce a voltage but cannot supply much current. A follower can reduce the load placed on the sensor while providing a more useful output to the next circuit stage.

Driving ADC inputs

An analog-to-digital converter (ADC) may draw brief input currents while sampling. A buffer can help the signal source drive that input, provided the op amp is suitable for the ADC’s requirements.

Buffering voltage references

A reference source may need to supply a stable voltage to several parts of a circuit. A follower can help isolate the reference from changing load conditions.

Active filters

Voltage followers are used in some active-filter designs to separate filter stages or prevent one stage from changing the behavior of another.

Sample-and-hold circuits

A buffer may be used around the sampling or holding components to reduce unwanted loading and help deliver the stored signal voltage to another stage.

Bridge and transducer circuits

Bridge sensors and transducers may produce small signals that should not be heavily loaded. A follower can provide a buffer before further signal conditioning.

Practical limits to check

A real voltage follower may not reproduce its input exactly. Before choosing an op amp, check:

  • Supply voltage: The input and output must stay within the device’s permitted operating range.
  • Input common-mode range: The input voltage must be within the range the op amp can sense.
  • Output-voltage swing: The output may not reach the supply rails.
  • Output current: The op amp must be able to drive the load.
  • Bandwidth and slew rate: These determine how accurately it can follow a changing signal.
  • Stability with capacitive loads: A long cable or large capacitor can make some followers unstable. Follow the datasheet’s recommendations.
  • Offset and bias errors: These can make the output differ slightly from the input.

The exact limits vary by op amp. For example, TI notes that designers should check the output operating range, bandwidth, output swing, and capacitive-load guidance for the selected device. TI buffer design notes

Common mistakes to avoid

  • Assuming a follower amplifies voltage. Its intended voltage gain is approximately one.
  • Assuming it can supply unlimited current. The output current is limited by the op amp.
  • Thinking the input signal provides the load power. The op amp’s supply rails provide most of the output energy.
  • Connecting the input to the inverting terminal by mistake. In a basic follower, the signal goes to the non-inverting input and the output feeds back to the inverting input.
  • Assuming the output always equals the input exactly. Real devices have offset, bandwidth, output-swing, and load limits.
  • Assuming a follower creates galvanic isolation. It buffers a signal but does not electrically isolate the circuits.
  • Ignoring capacitive loads. Some op amps need special precautions when driving large capacitances.

Conclusion

A voltage follower is an op amp connected with its output fed back to its inverting input and the signal applied to its non-inverting input. Its voltage gain is approximately one, so its output follows its input.

Its value is in buffering: the high-impedance input helps protect the source from loading, while the output can drive a suitable load using energy from the op amp’s power supply. This makes voltage followers useful with voltage dividers, sensors, ADC inputs, active filters, and reference circuits. Always check the chosen op amp’s supply, output-current, voltage-swing, bandwidth, and stability limits before using it.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top